>> Building Strik: 3D-Printed Tank Tracks, Toy Robot Servos, and Live ESP32-S3-CAM Video


Project Strik is officially starting to see and speak. The goal for this build is straightforward: put together a rugged, locally controlled, completely hackable telepresence rover using custom FreeCAD 3D-printed hardware, repurposed toy robot mechanics, and off-the-shelf microcontroller modules—zero proprietary cloud lock-in.

Strik rover parts laid out on the workbench including the 3D-printed tracked base, LiPo pack, L298N driver, ultrasonic sensor, and salvaged robot shells Strik rover parts laid out on the workbench including the 3D-printed tracked base, LiPo pack, L298N driver, ultrasonic sensor, and salvaged robot shells

1. The Lower Chassis: 3D-Printed Tank Tracks & Low-CG Power

Rather than buying a pre-fab rover frame, the lower drivetrain was designed from scratch and printed with heavy-duty rubberized treads and custom spur-gear reductions.

Close-up of the custom 3D-printed tracked chassis with the central battery bay and LiPo pack Close-up of the custom 3D-printed tracked chassis with the central battery bay and LiPo pack

  • Low Center of Gravity: A high-discharge LiPo pack (57.72Wh, 120C) sits tucked inside a custom-printed central battery bay right between the tracks to keep the rover planted on uneven terrain.
  • Motor Control & Power Rail: Drive power runs through an L298N dual H-bridge motor driver paired with an LM2596 buck converter to step raw battery voltage down to a clean, regulated 5V logic rail.

Bench layout of the L298N dual H-bridge motor driver, micro servo, HC-SR04 ultrasonic sensor, and 16x2 LCD Bench layout of the L298N dual H-bridge motor driver, micro servo, HC-SR04 ultrasonic sensor, and 16x2 LCD

2. Repurposing the Upper Torso & Geared Shoulder Servos

Instead of printing an entire humanoid shell from zero, Strik’s upper torso, head, and shoulder joints were salvaged from a retired toy robot chassis.

Disassembled black toy robot torso halves and internal hardware on the shop bench Disassembled black toy robot torso halves and internal hardware on the shop bench

Close-up of the salvaged robot shoulder joint bearing and housing Close-up of the salvaged robot shoulder joint bearing and housing

Inside the torso shell, a custom white 3D-printed mounting plate anchors dual micro servos geared directly into the shoulder rotation rings. Next up mechanically: aluminum tubing lands tomorrow to build out the forearms and manipulators so Strik can interact with objects on camera.

Custom white 3D-printed internal servo mount plate and geared shoulder drives inside the torso shell Custom white 3D-printed internal servo mount plate and geared shoulder drives inside the torso shell

3. Giving Strik Eyes & a Voice: ESP32-S3-CAM + MAX98357A Audio

To keep Strik lightweight, low-latency, and autonomous-ready, the head and electronics bay center around a GOOUUU ESP32-S3-CAM paired with a MAX98357A I2S Class-D mono amplifier.

GOOUUU V1.5 ESP32-S3-CAM board showing the camera ribbon connector and GPIO pinout GOOUUU V1.5 ESP32-S3-CAM board showing the camera ribbon connector and GPIO pinout

Audio Amp Harness & Isolation

The MAX98357A mounts directly behind the internal head speaker with short speaker leads and a full coat of hot glue across the back of the PCB to insulate the pins and lock the solder joints against gear vibration:

MAX98357A I2S Class-D amplifier wired up on the workbench before mounting MAX98357A I2S Class-D amplifier wired up on the workbench before mounting

MAX98357A amplifier mounted inside Strik’s head housing behind the speaker MAX98357A amplifier mounted inside Strik’s head housing behind the speaker

  • VIN (5V): Red
  • GND: Green
  • DIN (GPIO 40): Pink
  • BCLK (GPIO 41): Orange
  • LRC (GPIO 42): Yellow w/ Black Stripe

Salvaged robot head shell test-fitted with dual ultrasonic sensor eyes on the workbench Salvaged robot head shell test-fitted with dual ultrasonic sensor eyes on the workbench

Live POV Video Stream

Flashing the ESP32-S3-CAM directly from Arduino IDE (with OPI PSRAM enabled) immediately brought up a smooth, low-latency MJPEG video stream over local Wi-Fi—plus PWM control over the retina-searing onboard LED, which will double as a ported headlight for Strik’s night missions.

What’s Next on the Bench

  • Aluminum Arms: Cutting and fitting the aluminum tubing to the geared shoulder servos.
  • Two-Way Audio: Adding an INMP441 I2S MEMS microphone so Strik can listen as well as speak over I2S.
  • K3s & Local AI Integration: Bridging Strik’s live video, audio, and motor commands directly to the local K3s cluster so our local agents can drive and interact in meatspace.

Watch the latest bench progress & live camera test:
Strik Rover Live ESP32-S3-CAM & Audio Amp Build Short

Download the custom 3D-printed track & chassis files:
PiratesInTeepees on Printables